Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Trusted Air Duct Repair for Minneapolis Homeowners
Ductwork fails quietly. A seam opens behind a finished wall, a flex run gets crushed under a joist, and the room that was always the coldest in the house gets colder every winter. By the time the furnace starts short cycling or an upstairs bedroom never quite warms up, the leak has usually been there for more than one heating season. Our technicians have up to 14 years of experience tracing that kind of loss through Minneapolis homes, and we can schedule same-day visits when something needs eyes on it right away. Call (844) 320-5410.
Minneapolis homes pose a particular set of problems for ducts. The housing stock is old, the winters are long, and a lot of the duct trunk lines were sized for a furnace that was replaced two or three times over. When a contractor comes back with a quote for repair, you want to know what’s actually being done. We use Rotobrush and Nikro equipment on every job, and we carry Abatement Technologies gear for HEPA containment when the repair happens inside a living space. Our technicians are experienced, our work is insured and bonded, and every job starts with a written estimate and photos before and after. If you’ve ever been quoted a number over the phone that changed once a truck arrived, that’s the exact scenario we’re built to avoid.
HVAC Duct Installation
HVAC Duct Installation is the work of running new duct runs from a furnace or air handler to registers that don’t have them, or replacing an entire distribution system when the original layout no longer fits the equipment. Most of the calls we get for this in Minneapolis fall into two groups: an addition or a finished basement that needs supply and return, and an older home where the original trunk simply can’t handle a modern high-efficiency furnace’s airflow. Clover Air Duct Cleaning handles both, from the initial sizing walkthrough through the sealed, balanced finish. Typical whole-system installation in Minneapolis runs $2,400 to $6,800 depending on the number of runs, accessibility, and whether the system has to be reworked to fit existing framing.
Sizing and Layout
Static pressure and run length drive every decision here. A duct run that’s undersized for the room it serves shows up later as a room that never heats, and fixing that after drywall goes back up costs several times what it would have at the start. We measure the existing system and the room load before we plan a single run, and we’ll tell you when a duct you already have just needs a repair rather than a replacement.
Working With Existing Framing
Very few Minneapolis houses have the joist bays a duct run wants. We plan routing around plumbing, wiring, and structural members before anything gets cut, and we seal every joint with mastic and mesh rather than tape. Sealing matters here because a poorly sealed install loses more air than the original system did.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
Air Duct Replacement
Air Duct Replacement is a full removal and rebuild of tired, contaminated, or collapsing duct runs, rather than a patch. It’s usually the answer when flex duct has collapsed under years of insulation, when sheet metal has rusted through at the seams, or when the system was installed before current energy standards and every joint leaks. In Minneapolis, the homes most often needing replacement are those built between the 1940s and 1970s where the original ducts still serve a furnace that was never sized for them. Typical Air Duct Replacement in Minneapolis runs $1,800 to $5,200 depending on the number of runs and whether rigid or flex duct is used. Call (844) 320-5410 for a written estimate.
When Patching Stops Making Sense
If we find five separate failures across a single trunk line, it usually costs more to patch each one than to replace the run. We photograph each failure and show you the math before recommending replacement. That’s the difference between a suggestion and an upsell.
Materials and Sealing Standards
Replacement work typically uses rigid galvanized trunk line with short flex takeoffs to the registers, sealed at every joint with mastic and mesh. We work with Honeywell and Aprilaire indoor air quality equipment where filtration or fresh-air intake is part of the project. All replaced ductwork is sealed and verified before the system is turned back on.
Ductwork Repair
Ductwork Repair covers the targeted fixes that fall between cleaning and full replacement: sealing disconnected joints, repairing crushed flex runs, reconnecting registers that have come loose, and patching holes created by pests, remodels, or a contractor who didn’t check what was behind the drywall. Most Minneapolis homeowners call us about this because one room won’t heat, the furnace runs longer than it used to, or they can hear whistling at a register. Typical Ductwork Repair in Minneapolis runs $180 to $650 per repair, depending on access and location. Call us and we’ll give you a written number before any tool comes out.
Sealing Leaks at the Source
Tape and mastic failures at trunk transitions are the single most common leak we find on repair calls. On a cold Minneapolis winter, an open seam behind a knee wall can dump a meaningful portion of the heated air into the framing cavity before it ever reaches a register. We go after the actual failure point instead of sealing around it.
Access Without Cutting Into Finished Space
A lot of ductwork in this city sits behind plaster, above a finished ceiling, or in a joist bay that isn’t reachable from the basement. We plan access through the least invasive route we can find, then restore the opening. When a repair needs to happen in a living area, our Abatement Technologies containment equipment keeps dust out of the rest of the house.
Duct Replacement
Duct Replacement is what we call the work of swapping out a single failed section or run while leaving the rest of the system in place. It’s the right call when one room’s duct has collapsed inside a wall, when a flexible run has been stepped on during a remodel, or when a section of trunk has rusted through over the years. This is a good fit for Minneapolis homes with an older system where most of the ductwork is still fine. Typical Duct Replacement in Minneapolis runs $350 to $1,100 for a single run, depending on run length and access.
Isolating the Failed Run
Before we commit to replacing any run, we trace the airflow on both sides of it. If the trunk serving that run is fine, the job is contained and the cost stays predictable. If we find the same failure repeating in other sections, we’ll tell you so you can weigh that against replacement of the whole branch.
Matching What’s Already There
The replacement run needs to work with the furnace and the trunk it’s joining, not just fit inside the wall cavity. We size the new section to match the airflow the system is designed for, and we commission it once connected so the room sees the difference in the first heat cycle. Our technicians have up to 14 years of experience matching older systems like these.
Ductwork Installation
Ductwork Installation is the broader job of designing and installing a full duct distribution system, typically for new construction, a major renovation, or a home that has never had central ductwork. In the first two cases, you have a general contractor involved and drywall going up in a few weeks, so timing and layout matter as much as the install itself. In the third, this often means adding ducts through closets and soffits in a Minneapolis house that has only ever had radiators. Typical ductwork installation in Minneapolis runs $3,200 to $8,500 depending on the number of runs and whether the system is retrofit or new construction.
Coordination With a Build Schedule
On a renovation, the ductwork has to go in after framing and before insulation. We work from a set plan and stage the install so the trades after us aren’t waiting on us. Changes mid-build happen; we’ll flag them early so nothing gets buried behind drywall.
Retrofit Without Tearing the House Apart
Older Minneapolis homes often only had hydronic heat, so there’s no existing chase to follow. We route new ductwork through interior closets, soffits, and unused cavities wherever we can. That approach avoids opening finished walls in most cases, and it’s the difference between a smooth project and a very expensive one.
Brands We Service
We service Honeywell indoor air quality equipment and know how its zone controls and filtration components interact with the duct system. When a Honeywell bypass humidifier or an electronic air cleaner is part of the system, its duct connections are part of the repair scope, and we treat them that way rather than skipping past them to the furnace. We also work with Aprilaire filtration and fresh-air equipment, and we understand where these components create extra pressure on a duct run that’s already borderline.
Our cleaning and containment work runs on Rotobrush and Nikro professional equipment and Abatement Technologies systems, so the brand names behind our own service reflect the same standard we hold the equipment we service to. We don’t claim to be a dealer for any particular brand; our role is to understand how the equipment in your home actually behaves, whether it was installed last year or twenty years ago. Whether you have Honeywell or Aprilaire, or any other make, we can help. Call (844) 320-5410.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Whistling or rattling at a register. A whistle usually means the pressure behind that register is too high, which points to a restriction somewhere downstream. Left alone, it taxes the blower and shortens the furnace’s life.
- A room that won’t heat no matter what you do. One cold room when the rest of the house is fine is almost always a duct issue, not a furnace issue. The most common cause is a disconnected or crushed run that’s been quietly costing you heat for years.
- Visible dust trails at joints or around vents. Dust collected at a particular seam is a sign air is being pushed out through that seam, not through the register. Those leaks pull attic or crawl space air into the system.
- Higher energy bills with no change in habits. A duct that leaks delivers less conditioned air for the same run time. If your bill jumps and the weather is even close to last year, the ductwork is worth checking.
- Musty smell when the system kicks on. Damp air entering through a disconnected return can carry odor from a crawl space or basement into living space. That’s a strong sign a return-side connection has failed.
Our Process, Step by Step
- 1
Walkthrough and airflow check. We walk the system with you, note the rooms that aren’t comfortable, and take static pressure readings at the air handler. Those readings tell us whether the system is starving for air or has too much resistance, and they guide everything after.
- 2
Camera inspection of the duct runs. Where we can’t see the duct, we run a camera through it. This is how we catch a duct that’s collapsed inside a wall versus one that’s just dirty inside the same wall.
- 3
Written estimate with photos. You get the failure points photographed, the scope spelled out line by line, and a single flat price for the work. Nothing starts until you’ve approved the number.
- 4
Contained repair work. Repairs happen with proper containment in place. If we’re opening a wall or ceiling, we plan the opening and the patch as part of the job. Rotobrush and Nikro equipment handles cleaning of adjoining duct runs so dust doesn’t migrate during the work.
- 5
Post-repair verification. We recheck static pressure, confirm each repaired run is delivering airflow to the room, and show you before-and-after photos. If a number we promised didn’t happen, we don’t close the job until it does.
How Much Does Air Duct Repair Cost in Minneapolis?
Air duct repair in Minneapolis typically runs $180 to $650 for a single repaired joint or reconnect, $350 to $1,100 for a single replaced run, and $1,800 to $5,200 for full replacement of a duct system. HVAC duct installation runs $2,400 to $6,800, and full ductwork installation in a retrofit or new build runs $3,200 to $8,500. Those ranges are typical, not fixed; the written estimate sets the final price.
What moves the number most is access. A repair at an open basement ceiling costs a fraction of the same repair inside a plaster wall with a finished room on the other side. Run count matters too, and so does whether the existing duct is rigid sheet metal or flex. Flex is easier to repair but the repairs don’t last as long when the flex has already been crushed, and knowing that up front saves you from paying twice.
To avoid overpaying: ask for the estimate in writing, ask for photos of the failure before work starts, and be suspicious of any number quoted over the phone without a look. Repair prices also get inflated when a single small failure is presented as a reason to replace the whole system. We only recommend replacement when the repair cost genuinely exceeds the replacement cost for the same branch, and we’ll show you where that line is.
Every estimate we give is free and no-obligation. It includes the scope in plain language, the price for that scope as one flat number per system, and before-and-after photos when the work is done. Call (844) 320-5410 with your details and we’ll get you scheduled. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Our Service Area Near Minneapolis
We serve homeowners across Minneapolis and the surrounding west metro, including Golden Valley, St. Louis Park, Robbinsdale, Columbia Heights, Richfield, Roseville, Edina, Crystal, Hopkins, Brooklyn Center, and New Hope. Most Minneapolis addresses fall into a same-day or next-opening window depending on schedule, and the surrounding suburbs are similar. If you’re in a farther edge of the service area, we’ll give you a realistic window on the call. Compare duct cleaning and repair service across the metro at Minneapolis to see how we approach each suburb differently.
Serving Minneapolis, MN – Our Local Coverage Area
We serve Minneapolis and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Air Duct Repair in Minneapolis
Air duct repair is fixing the physical system that carries conditioned air from your furnace to the rooms of your house. It covers sealing disconnected joints, replacing crushed or collapsed runs, reconnecting loose registers, and patching holes. It’s different from duct cleaning, which removes debris rather than fixing structure, and different from replacement, which is a full rebuild of the duct runs. Most repair visits focus on the two or three specific failure points that are actually costing you comfort.
Most single-point repairs take one to two hours once we’re on site. A replaced run typically takes two to four hours. Duct replacement across a full branch or a full system can take a full day or more, especially when the ductwork sits behind finished walls and the opening and restoration are part of the job. We give you a realistic time window in the estimate so you can plan around it, and we’ll let you know if the scope changes once work starts.
Most repairs in Minneapolis fall between $180 and $650 for a single point, with a replaced run running $350 to $1,100, and full replacement at $1,800 to $5,200. Those are typical ranges; the written estimate always sets the final price. The biggest factor is access. Call (844) 320-5410 for an exact quote, and estimates are free.
Yes, we service duct systems connected to Honeywell and Aprilaire indoor air quality equipment. That includes bypass humidifiers, electronic air cleaners, and the filtration and fresh-air components these brands make. When the duct connection to that equipment is part of the failure, it’s part of the repair scope. We also work with Guardsman components where they’re already installed, and we’re familiar with how they behave as part of the broader duct system.
Yes, we schedule same-day repair when the day’s schedule allows. Our dispatch runs from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. If you call outside dispatch hours, we book you into the next opening. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Our work is backed by a workmanship guarantee on the repairs we perform, and we’ll spell out the exact coverage in writing on your estimate. Every job includes before-and-after photos you keep, so you have a record of what was repaired and how. If something we repaired fails within the covered window, we come back and make it right. We won’t promise coverage we can’t back up in writing.
Clear access to the furnace, any visible duct runs, and any closet or crawl space where you know ductwork runs. Move items away from the wall or ceiling where we might need to open access. Shut off any window units or portable units, and let us know if anyone in the house has allergies or sensitivities so we can plan containment. Beyond that, you don’t need to do anything. Call (844) 320-5410 with your address and we’ll take it from there.
Schedule Your Air Duct Repair Service in Minneapolis Today
If a room in your Minneapolis house hasn’t heated right in more than one season, or your energy bill has crept up with no explanation, the ductwork is the first place to look. Call (844) 320-5410 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Every job comes with a flat per-system price, before-and-after photos, and insured and bonded technicians. Our technicians have up to 14 years of experience.
Written by the team at Clover Air Duct Cleaning.